Ремонт потолка    Фальшпотолки из гипсокартонаPro-Remont.com Repair of plasterboard ceiling Falshpotolki

Falshpotolki of plasterboard

Falshpotolki of plasterboard is a simple and cheap solution for the premises where falshpotolka dictated by the need to cap off stubborn slump. In our view they are not desirable in the space of communication, passing beneath the ceiling because falshpotolok of plasterboard is collapsible and seriously complicate the lines of communication services after installation.

Another application of plasterboard falshpotolka-a complex, multi-surface floor in the premises of the original design. Podatlivost material creates ceilings with tabs and increasing complex forms, mounted in a ceiling light any elements and even combine it with other materials and ceiling systems. Falshpotolki of plasterboard functionally designed for the surface, do not have their own design and applied as a surface for the application of paint - or wall-how or finishing material.

Instructions

Gipsokartonovy falshpotolok may be mounted in the pendant, and podshivnom option, ie hinged on the scaffold at a considerable distance from existing floors, or fastened by sending directly to the floors. Since falshpotolok of plasterboard is relatively high weight and is intended for future maintenance, it must be rigid frame, ie exclude various design variations that can cause cracks in the decorated surface.

For mounting podshivnogo plasterboard ceiling of the best take advantage of the special metal profiles, which are sold to any company selling these devices. Profile mounted directly from the ceiling, vyravnivayas with wooden wedges driven between the profile and the current ceiling, so that we get a crate the size of a cell 60h40 cm, and the province gipsokartonovyh sheets were in the skin around the centre profile. Sheathing glass sheets plasterboard should be done so that the edges of sheet width of the gap remained about cm step attachment self exceeds 20 cm to cover the carcass in a single layer board used Sormat length of 25 mm and a diameter of 30 and 35 mm. The assembly must take into account the carcass weight construction and use only a material part of the existing hardware. In case falshpotolok be factored lighting, ventilation or air conditioning, it is necessary to measure their height and install thus minimum gap between existing floors and falshpotolkom adequate for their deployment. If the installation of lighting and other equipment required distance of more than a high profile special, it is necessary to increase the gap, attaching to the existing wooden floors insert the desired thickness, which will have a profile (so they went to sites glass), or change the design of a traveling version.

When selecting a traveling version falshpotolka of plasterboard, special attention should be paid to frame rigidity.

Frame in this case will be a kind of two parts, glass, which are mounted sheets of plasterboard, and the pendant system, tightly linking the crate with the existing floors. Crate is the same version podshivnogo ceiling, but that the additional profile passing over it. Hanging system perform better in a stretch of 2-x sections reinforced bar diameter of about 12 mm, threaded control nozzle connected with the locking kontrgaykami.

Such a system, on the one hand, will conveniently manage horizontal ceiling, and to give sufficient rigidity suspension.

Finishing falshpotolka surface of plasterboard is like finishing any gipsokartonovoy surface. The first step is to fill the seams between the sheets of the remaining shell, putty and putty putty deepening of self, which is attached to the skin cage. It is best suited for this purpose coating "Fugenfuller" produced by "TIGI Knauf" - one of the leading plasterboard production and materials. Then all seams carefully prokleivayutsya construction dressing-serpyankoy.

It is recommended to use the sieve serpyanku reminding appearance mosquito net width of 50 mm. This serpyanka offers higher strength and, with the relatively large mesh nets, allowing the surface "breathe" predohranyaya of a "hair" cracks. Then again shpatlyuyutsya beads and carefully zashlifovyvayutsya.

The surface so color can be almost any type of paint (with the use of the soil), okleivat different types of film or paper coatings, polymer or cork tiles. If you are going to paint a ceiling water-colours, or other water-based paint, recommended that the entire surface proshpatlevat ceiling on sdir ", ie superfine layer putty on the evidence of microstructure and properties of the surface pores.

Author : Vyacheslav Then
Source :